Standard Tool Kit
 

There was no tool kit with the 2001 GZ250 that I bought in Aug. Does anyone know where I can get a replacement standard tool kit.

Are they the same for all Suzukis? So that if I find one for sale for a different model it would also work for the 250?

John B

Re: Standard Tool Kit
 

http://www.gz250bike.com/forum/viewt...hp?f=10&t=1651

Try the search. It works.

:biggrin:

Re: Standard Tool Kit
 

Sarris, thanks. You came through again. You are right. As a newbie, I probably won't have any questions that haven't already been asked and answered. I will try a search first from now on.

Re: Standard Tool Kit
 

John,

If it's a question that has only one answer, search is your friend. However, lots of answers are a matter of opinion. The site has added a lot of new users this year, and they may not have participated in older threads. So, don't hesitate to weigh in on an old subject - keeps things interesting.

-Fellow newb

(If you really want to stir things up, post to the "turn your 250 into a 350" thread. That one is like pouring gas on the "flames.")

Re: Standard Tool Kit
 

Here is the contents of my tool kit:

1 Wrench Spark Plug Needs Screw Driver Bit.
1 Screwdriver Handle
1 Screwdriver Bit 3 Phillips Fits Screwdriver Handle
1 Screwdriver Bit 1/4 and 2 Flat/Phillips Fits Screwdriver Handle Combination
1 Axel Wrench 19mm 6 Point Box For Loosening rear axle nut. Used with extension handle.
1 Extension Handle Fits 19mm Axle Wrench
1 Pliers Slip Joint Small and thin slightly better than nothing.
1 Wrench 14/17mm Open End
1 Wrench 12/10mm Open End
1 Wrench 6mm Hex/Allen
1 Wrench 4mm Hex/Allen

You might want to consider rolling your own tool kit. The factory tools are not very good.

Re: Standard Tool Kit
 

If you have the Plexistar II add in a 19mm to tighten, loosen the lockdown nut for the handlebar struts.

Re: Standard Tool Kit
 

You'd be better served by using Badbob's guide of what is contained in the factory tool kit and replacing them with quality tools.
That's what I did.
Also, keep the factory tool kit on hand, if you get one, so you can pass it along when you sell the bike later. It gives the appearance of being a well organized owner. :)

Re: Standard Tool Kit
 

As it has been said many times, the factory tool kit is just a template for a real tool kit. Also toss in a couple cotter pins and real pliers for a chain adjustment. Extra fuses take up little room too. I also carry a 4 inch crescent wrench, small but comes in handy for rounding off small stuff. When leaving for a longer ride I also include a 1/4 inch socket set, a couple extensions and a swivel connector for hard to reach places. If you take it you won't need it of course. If you don't take it Murphy's Law will strike you down. Handy Wipes and a first aid kit to repair body damage is helpful. Learned most of this stuff from people who didn't check their bikes and do maintenance very well. Years ago I was the designated Hero with Tools.

Re: Standard Tool Kit
 

Buy or make a set of jumper cables to add to the tool kit. I made a set 10' long of 10 gauge wire which is heavy enough to carry the load of the starter and neatly fits folded up in the underseat compartment with everything else. Use the smaller size terminal clamps.
You never know when you may have a dead battery (like from leaving the parking light on as some of those on here have done).

Re: Standard Tool Kit
 

+1 for fuses - if it is an intermittent problem the one spare on the bike will not get you to a safe haven. I know this from personal experience. Try changing the fuses in your GZ and you will soon see why I carry needle nose pliers.

I like the 1/4 socket set too. I don't carry a full set. Just the ones that I need. I also carry an adapter 1/4 to 3/8 to use the 1/4 inch ratchet with my 3/8 spark plug socket.

+1 for jumper cables. I got them and have needed them.

A roll of high quality electrical tape. I recommend 3M.

A flattened roll of duct tape. You can buy small rolls or use one that is almost used up. Get good stuff and put all of your tape in a plastic bag.

Cable ties and something you can cut them with. At least eight inches. These have got me home when a bolt broke.

I need to write a post about my tool kit. Something else to do. :cry:

Re: Standard Tool Kit
 

Speaking on small ratchet sets, Autozone has marked down all of their AmPro tools at least 65% off.
I purchased a very nice quality set of 1/8 drive metric ratchers for $8.88. It doesn't come with a drive extension, but everything else is in there that you'll need on the bike, unless you are changing a tire or something major.

This sale has been going on for a while but, for some reason, it's just not selling.

Re: Standard Tool Kit
 

BB- you need a bigger bike just to carry all those tools and spare parts (just kidding).
Do they all fit in one ammo bag? And you keep it locked up, right? (reference to another post on here nearby).
The GZ is not unreliable but it pays to be prepared for any eventuality, especially if you cruise away from home. Self sufficiency is one of the greatest attributes, whether it be on a bike, a boat, a car, or in anything else.
Nice tool list - how much do you think all that weighs?. Speaking of list, having it all in one bag or ammo can probably will give the bike a list. :2tup:

Re: Standard Tool Kit
 

Details, details.
Does strapping a lot of weight on the carrier behind the passenger seat make it easier to wheelie ??? :crackup

Re: Standard Tool Kit
 

Locked yes. Always even when empty.

The tools listed would fit in one ammo can easy.

I have no idea what it weighs.

This is not even 1/4 what I carry on a road trip.

Re: Standard Tool Kit
 

BB - What kind of lock do you have on your cans? Any pictures?

Re: Standard Tool Kit
 

I don't have any photos specifically of the locks. Maybe I should make some. There are some fancy locks you can get for ammo cans that cost way more than I paid for the cans. I just used a stainless steel eye bolt and a padlock.

http://www.robertkeeney.com/gallery/...ers_SAW_01.jpg

http://www.robertkeeney.com/gallery/...ers_SAW_04.jpg