Forum: Troubleshooting
03-26-2019, 06:16 PM
|
Replies: 10
Views: 11,280
The two bolts on the back arms of the swing arm...
The two bolts on the back arms of the swing arm are used to adjust wheel alignment in the swing arm. The chain should run true between the two sprockets when it is adjusted correctly. Also have the...
|
Forum: General GZ250 Talk
03-18-2019, 05:55 PM
|
Replies: 16
Views: 31,818
While it would be relatively inexpensive to fix...
While it would be relatively inexpensive to fix with used parts from ebay. I would be very suspicious of the geometry of rest of the frame. If it is tweaked, which is very possible given the front...
|
Forum: Performance
10-13-2018, 08:34 AM
|
Replies: 12
Views: 102,120
87 Octane Ethanol free. I don't ride my GZ as...
87 Octane Ethanol free. I don't ride my GZ as much, Ethanol starts to go bad in a few weeks so I don't want it sitting in the tank. I also add a little Marvel Mystery Oil to the gas at each fill...
|
Forum: General Maintenance
09-04-2018, 12:25 PM
|
Replies: 8
Views: 15,512
|
Forum: General Maintenance
08-20-2018, 05:17 PM
|
Replies: 1
Views: 6,280
|
Forum: General GZ250 Talk
08-01-2018, 02:31 PM
|
Replies: 8
Views: 9,307
|
Forum: General Maintenance
07-26-2018, 02:58 PM
|
Replies: 8
Views: 7,751
Most of the electrical connections terminate in...
Most of the electrical connections terminate in the headlight bucket. Take the light out and look in there for anything obvious, loose connections, burnt wires ect. If that fails you really need a...
|
Forum: General GZ250 Talk
07-20-2018, 10:32 AM
|
Replies: 7
Views: 23,653
|
Forum: Troubleshooting
05-25-2018, 11:29 PM
|
Replies: 8
Views: 25,219
|
Forum: Troubleshooting
05-17-2018, 11:01 PM
|
Replies: 8
Views: 25,219
|
Forum: Troubleshooting
05-17-2018, 10:59 PM
|
Replies: 11
Views: 32,927
|
Forum: Troubleshooting
05-17-2018, 06:09 PM
|
Replies: 11
Views: 32,927
|
Forum: Troubleshooting
05-15-2018, 06:14 PM
|
Replies: 6
Views: 7,732
There is a rod (rear torque link) that connects...
There is a rod (rear torque link) that connects between the drum housing and the frame that prevents the shoe assembly from rotating with the braking forces. Check the fasteners and make sure they...
|
Forum: Troubleshooting
05-09-2018, 05:38 PM
|
Replies: 2
Views: 4,125
did you clean and service the idle circuit and...
did you clean and service the idle circuit and o-ring under the brass plug on the bottom? Even if it seems to idle ok that circuit can cause problems when the throttle plate is opened.
You might...
|
Forum: Parts & Accessories
05-02-2018, 03:38 PM
|
Replies: 20
Views: 22,066
|
Forum: Parts & Accessories
04-30-2018, 04:22 PM
|
Replies: 20
Views: 22,066
|
Forum: Parts & Accessories
04-30-2018, 09:50 AM
|
Replies: 20
Views: 22,066
|
Forum: Troubleshooting
04-23-2018, 11:36 PM
|
Replies: 1
Views: 4,477
|
Forum: Parts & Accessories
04-18-2018, 12:55 PM
|
Replies: 20
Views: 22,066
|
Forum: Parts & Accessories
04-18-2018, 11:00 AM
|
Replies: 20
Views: 22,066
|
Forum: Member Introductions
04-11-2018, 05:21 PM
|
Replies: 7
Views: 4,901
|
Forum: Troubleshooting
03-28-2018, 06:17 PM
|
Replies: 13
Views: 10,627
You might also use a meter on the disconnected...
You might also use a meter on the disconnected ground wire and test for voltage being shorted to ground. One probe on the ground wire and the other on the battery negative terminal. There should be...
|
Forum: Troubleshooting
03-28-2018, 04:57 PM
|
Replies: 13
Views: 10,627
Check the side stand switch and the side stand...
Check the side stand switch and the side stand relay. I was looking over the wiring diagram and those two look like they could be suspect. I would pull the side stand relay and disconnect the side...
|
Forum: Troubleshooting
03-28-2018, 04:34 PM
|
Replies: 13
Views: 10,627
|
Forum: Troubleshooting
03-28-2018, 10:11 AM
|
Replies: 13
Views: 10,627
I tried replacing my stock ignition switch with...
I tried replacing my stock ignition switch with an aftermarket when I first got my bike due to not having the key. The aftermarket switch would blow the 20 amp main fuse every time I went to turn it...
|