Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: anesde
Forum: Troubleshooting 06-09-2015, 08:22 PM
Replies: 33
Views: 8,195
Posted By anesde
One thought - when I remounted the carburetor it...

One thought - when I remounted the carburetor it was very difficult to ensure it was properly inside both rubber hose clamps (airbox and engine).

I'll double check theres no leaks once engine...
Forum: Troubleshooting 06-09-2015, 08:19 PM
Replies: 33
Views: 8,195
Posted By anesde
Seafoam and a 25 mph ride and it runs slightly...

Seafoam and a 25 mph ride and it runs slightly better but still won't go above 45.

I have a couple of coworkers who have a compression kit and a way to check the vacuum so I'll check that out...
Forum: Troubleshooting 06-08-2015, 09:19 PM
Replies: 33
Views: 8,195
Posted By anesde
I put in the oil with a calibrated measuring cup...

I put in the oil with a calibrated measuring cup and verified it's at the line while bike is upright.

I tightened the screw (the locknut was a BITCH to loosen) and backed it out a quarter turn...
Forum: Troubleshooting 06-02-2015, 07:42 AM
Replies: 33
Views: 8,195
Posted By anesde
Also, I think part of the problem is that the...

Also, I think part of the problem is that the manual did not convert the required torque correctly, nor apparently use the correct units. It specifics 10 N-m for the 4 bolts that hold the clutch...
Forum: Troubleshooting 06-02-2015, 07:01 AM
Replies: 33
Views: 8,195
Posted By anesde
Not yet. I took the whole thing apart again...

Not yet. I took the whole thing apart again yesterday and the put on new steel plates on. Triple checked that all the parts were in there and in the correct order and then put everything back...
Forum: Troubleshooting 05-24-2015, 06:45 PM
Replies: 33
Views: 8,195
Posted By anesde
Yes I did soak the plates overnight. Used...

Yes I did soak the plates overnight. Used motorcycle oil this time. Going to bite the bullet and buy the whole new assembly instead of messing around with trying to clean up the current plates.
...
Forum: Troubleshooting 05-23-2015, 01:18 PM
Replies: 33
Views: 8,195
Posted By anesde
I found it hard to believe that oil was the only...

I found it hard to believe that oil was the only culprit. Bought new clutch plates and took the clutch apart this morning. Clutch plates had nothing on them and friction plates were scoured and...
Forum: Troubleshooting 05-16-2015, 08:46 PM
Replies: 33
Views: 8,195
Posted By anesde
Also I did check the clutch and it's correct. And...

Also I did check the clutch and it's correct. And yes it revs up strong and loud. Too loud actually, I changed the idle screw to the bare minimum. Do you think that may have something to do with it?
Forum: Troubleshooting 05-16-2015, 08:44 PM
Replies: 33
Views: 8,195
Posted By anesde
Changed the oil two months ago and used synthetic...

Changed the oil two months ago and used synthetic royal purple 10w-40. Also changed spark plug back then - guy at Napa told me it was NGK DCPR8E

I thought it was the oil so I changed back today to...
Forum: Troubleshooting 05-11-2015, 11:48 AM
Replies: 33
Views: 8,195
Posted By anesde
Changed the air filter and still have the same...

Changed the air filter and still have the same issue. Went from 2.5 turns on pilot screw to 1.75 turns and no change either.

From what I read it seems that this could be a symptom of a slipping...
Forum: Troubleshooting 05-09-2015, 10:40 AM
Replies: 33
Views: 8,195
Posted By anesde
No Acceleration at 40MPH

I did a search and couldn't find anything so I figured I'd start a new topic. I've been getting to know my 2003 gz250 in the past month and from what I've read about top speeds and acceleration I...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 11:02 PM.

Contact Us - GZ250Bike.com - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.