Counter wight handle bar

New GZ250 · 08-27-2013, 05:27 PM

The end cap/counter weight has come loose/off on my bike. The long bolt does not want to screw back in, think nut has fallen off in throttle twist assembly. Any idea how to reconnect, or just say screw it?

5th_bike · 08-27-2013, 08:31 PM

You will probably have to remove the rubber cylinder from the inside of the handlebar first.
If you ruin it in the process, just order a new one.
Then, when you put the bike on its side, the nut will fall out of the handle bar (mine did)
Reconnect, finger tight, push back in, tighten further.

For a parts list and figure, see:
http://www.mrcycles.com/fiche_sectio...003&fveh=10117
(parts 2 through 8; part #7 is the rubber expansion cylinder, and part #8 is the nut in your handlebar)

alantf · 08-28-2013, 04:27 AM

To get the rubber out, try bending the end of a wire coat hanger into a hook, then pushing it through the rubber, and pulling it out.

**jonathan180iq** · 08-28-2013, 08:40 AM

If leaning it over doesn't cause it to fall out of the bar, put a coffee filter over the end of your wet/dry vac and suck it out. The filter will keep it from getting sucked into the vaccuum.

New GZ250 · 08-29-2013, 02:22 PM

I have to assume the world will not end with the counter weight, or will it? A bit more vibration? How about super gluing it on? :roll:
Me Gordon

alantf · 08-30-2013, 04:23 AM

Seems to me that the only thing the weights do is stop the mirrors getting too much damage when the bike goes down. :roll: (they hit the road first)

08-27-2013, 05:27 PM	#1
New GZ250 Senior Member Join Date: May 2009 Location: Palo Alto, CA Posts: 297	Counter wight handle bar The end cap/counter weight has come loose/off on my bike. The long bolt does not want to screw back in, think nut has fallen off in throttle twist assembly. Any idea how to reconnect, or just say screw it? Login or Register to Remove Ads
	0

08-27-2013, 08:31 PM	#2
5th_bike Senior Member Join Date: Oct 2007 Location: HoCo, Maryland Posts: 1,349	Re: Counter wight handle bar You will probably have to remove the rubber cylinder from the inside of the handlebar first. If you ruin it in the process, just order a new one. Then, when you put the bike on its side, the nut will fall out of the handle bar (mine did) Reconnect, finger tight, push back in, tighten further. For a parts list and figure, see: http://www.mrcycles.com/fiche_sectio...003&fveh=10117 (parts 2 through 8; part #7 is the rubber expansion cylinder, and part #8 is the nut in your handlebar) __________________ 2005 "Saturn Black", stock + tach
	0

08-28-2013, 04:27 AM	#3
alantf Senior Member Join Date: Nov 2008 Location: Tenerife (Spain) Posts: 3,715	Re: Counter wight handle bar To get the rubber out, try bending the end of a wire coat hanger into a hook, then pushing it through the rubber, and pulling it out. __________________ By birth an Englishman, by the grace of God a Yorkshireman. Login or Register to Remove Ads
	0

08-28-2013, 08:40 AM	#4
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	Re: Counter wight handle bar If leaning it over doesn't cause it to fall out of the bar, put a coffee filter over the end of your wet/dry vac and suck it out. The filter will keep it from getting sucked into the vaccuum.
	0

08-29-2013, 02:22 PM	#5
New GZ250 Senior Member Join Date: May 2009 Location: Palo Alto, CA Posts: 297	Re: Counter wight handle bar I have to assume the world will not end with the counter weight, or will it? A bit more vibration? How about super gluing it on? :roll: Me Gordon Login or Register to Remove Ads
	0

08-30-2013, 04:23 AM	#6
alantf Senior Member Join Date: Nov 2008 Location: Tenerife (Spain) Posts: 3,715	Re: Counter wight handle bar Seems to me that the only thing the weights do is stop the mirrors getting too much damage when the bike goes down. :roll: (they hit the road first) __________________ By birth an Englishman, by the grace of God a Yorkshireman.
	0