Oil on Cylinder ,?

leonj2932 · 06-15-2017, 12:54 AM

Hey guys I'm about confused as to why there's baked on oil on the cylinder where the fins are , I tried removing it with engine degreaser but it's really baked on . I hope this isn't due to an engine issue

u

I attached a picture for if anyone has any ideas to what may be going on or how that oil got there .

spldart · 06-15-2017, 01:54 AM

Could be the valve adjust covers. Could be the head gasket.
I've fought with this problem too.

leonj2932 · 06-15-2017, 12:17 PM

How do you fix the problem though ? Or is it something that isnt a huge priority ??

alantf · 06-16-2017, 04:54 AM

With the GZ, the head bolts seem to come loose over time. You could try tightening them first. Also check the bolts holding the exhaust, and the valve adjuster cover. Caveat - Make sure you don't shear them.

RJsfishin · 06-20-2017, 09:41 AM

Quote:

Originally Posted by leonj2932

How do you fix the problem though ? Or is it something that isnt a huge priority ??

First of all, is it a problem ??
You said its old baked on oil, that's probably been there forever,...possibly leftover from a prior leak ?
You never said anything about it leaking oil,....like running down the cyl and onto the floor.
My advice, if it ain't broke, don't fix it.
Summed up, from what you described, you don't have a problem.

leonj2932 · 07-10-2017, 10:21 PM

no sorry , its definetely something, when i bought the bike there was no oil, 1000 miles later and im just a mess with this bike still.

wickedp34 · 09-26-2017, 01:28 PM

I'm dealing with the same issue. Baked on and burnt oil on the cooling fins. When it heats up, it drips onto the fins and causes smoke. I finally wanted to investigate where exactly it was coming from. I used degreaser and eblow grease and got rid of what was already there. I took the header side cover off and started up the bike. I let it heat up and watched really closely. Finally figured out it is coming from a cap above where the exhaust connects to the header. I looked in the manual and it is labeled as an inspection cap. I'm gathering there is probably a seal behind it that is not doing its job. It could also be the bolts aren't tight enough. Before I attempt to do anything with it, I'd like some input. If I remove that cap to inspect the gasket, will there be a good deal of oil coming out of it? Also, when I replace the cap and tighten the bolts, do those particular bolts need a torsion wrench? Thanks in advance!

5th_bike · 09-29-2017, 08:24 PM

Looking at the picture, it could have been something (clothing, glove) that melted and left some on the fins. Can't really see on top of the fins though.

PS Wickedp34, no problem, open valve cover, replace gasket. No oil will come out (provided engine is off....). Yes, torsion is in the manual that you can download from somewhere here.

Pmhearns · 06-16-2017, 09:34 AM

Remove the side covers and look with a flash light if you have oil gathering in the pocket where both the spark plug is and the left front head stud are. If there is pooling there, youre likely leaking oil from the washer/gasket of the nut. DONT JUST TIGHTEN THE NUT! The BEST thing to do is now check for oil around the head gasket, if its clear... order the oem washers and gaskets for the head studs, And some quality grey gasket maker. Remove the valve cover, set it aside. Loosen(no need to remove completlly unless you are changing head gasket) the bottom nuts on the guide studs on the under side of the head, Now, remove each nut and the washer one at a time and MAKE NOTE of whether its a washer or a gasket. Then replace the used washer with the correct new one. I believe the gaskets (copper washer) go to the 2 studs inside the valve cover but not 100% sure.. i applied a small amount of low strength locktite to the inside of the nut... now finger snug 1 by 1 in cross pattern. The using a torque wrench, i tighten to roughly 20% of oem torque spec then cross to next stud and repeat in cross pattern until reached 100%. Then retorque the guide nuts... CLEAN ALL OLD GASKET RESIDUE FROM HEAD AND COVER. . I use methonal for this but alocol will work woth a fine grit scotch brite pad. Very fine bead of new gaset on cover and replace. Torqing bolts in same manner as head studs. It seems like a lot of work but abkut an hour and you will leak free for a long time

Also, it helps to replace those crappy stock header bolts with ss set screws... i think i used 30mm and they are 6x1.0 mm threads. I threaded them until they bottom out and back oit 1 full turn, then used lock nut to tighten them down that way you arent tightening up on the threads in the head..

If you DO have oil on the underside of the head, replace headgasket and repeat sll steps. And dont forget to mind the timing chain.... use a hammer to hold it up after you move the cam becsue if it drops, youre gonna have a bad time... also, buy new header gaskets.....

Phew...

leonj2932 · 06-19-2017, 12:10 AM

wow that sounds like a lot of things to do , ugh this bike has been nothin but problems so far .

06-15-2017, 12:17 PM	#3
leonj2932 Member Join Date: May 2017 Location: San Francisco/Bay Area Posts: 31	How do you fix the problem though ? Or is it something that isnt a huge priority ?? Login or Register to Remove Ads
	0

06-16-2017, 04:54 AM	#4
alantf Senior Member Join Date: Nov 2008 Location: Tenerife (Spain) Posts: 3,715	With the GZ, the head bolts seem to come loose over time. You could try tightening them first. Also check the bolts holding the exhaust, and the valve adjuster cover. Caveat - Make sure you don't shear them. __________________ By birth an Englishman, by the grace of God a Yorkshireman.
	0

09-26-2017, 01:28 PM	#7
wickedp34 Junior Member Join Date: Sep 2017 Posts: 2	Same issue I'm dealing with the same issue. Baked on and burnt oil on the cooling fins. When it heats up, it drips onto the fins and causes smoke. I finally wanted to investigate where exactly it was coming from. I used degreaser and eblow grease and got rid of what was already there. I took the header side cover off and started up the bike. I let it heat up and watched really closely. Finally figured out it is coming from a cap above where the exhaust connects to the header. I looked in the manual and it is labeled as an inspection cap. I'm gathering there is probably a seal behind it that is not doing its job. It could also be the bolts aren't tight enough. Before I attempt to do anything with it, I'd like some input. If I remove that cap to inspect the gasket, will there be a good deal of oil coming out of it? Also, when I replace the cap and tighten the bolts, do those particular bolts need a torsion wrench? Thanks in advance!
	0

09-29-2017, 08:24 PM	#8
5th_bike Senior Member Join Date: Oct 2007 Location: HoCo, Maryland Posts: 1,349	Looking at the picture, it could have been something (clothing, glove) that melted and left some on the fins. Can't really see on top of the fins though. PS Wickedp34, no problem, open valve cover, replace gasket. No oil will come out (provided engine is off....). Yes, torsion is in the manual that you can download from somewhere here. __________________ 2005 "Saturn Black", stock + tach Last edited by 5th_bike; 09-29-2017 at 08:47 PM. Reason: Added.
	0

06-16-2017, 09:34 AM	#9
Pmhearns Member Join Date: Jan 2017 Posts: 54	Remove the side covers and look with a flash light if you have oil gathering in the pocket where both the spark plug is and the left front head stud are. If there is pooling there, youre likely leaking oil from the washer/gasket of the nut. DONT JUST TIGHTEN THE NUT! The BEST thing to do is now check for oil around the head gasket, if its clear... order the oem washers and gaskets for the head studs, And some quality grey gasket maker. Remove the valve cover, set it aside. Loosen(no need to remove completlly unless you are changing head gasket) the bottom nuts on the guide studs on the under side of the head, Now, remove each nut and the washer one at a time and MAKE NOTE of whether its a washer or a gasket. Then replace the used washer with the correct new one. I believe the gaskets (copper washer) go to the 2 studs inside the valve cover but not 100% sure.. i applied a small amount of low strength locktite to the inside of the nut... now finger snug 1 by 1 in cross pattern. The using a torque wrench, i tighten to roughly 20% of oem torque spec then cross to next stud and repeat in cross pattern until reached 100%. Then retorque the guide nuts... CLEAN ALL OLD GASKET RESIDUE FROM HEAD AND COVER. . I use methonal for this but alocol will work woth a fine grit scotch brite pad. Very fine bead of new gaset on cover and replace. Torqing bolts in same manner as head studs. It seems like a lot of work but abkut an hour and you will leak free for a long time Also, it helps to replace those crappy stock header bolts with ss set screws... i think i used 30mm and they are 6x1.0 mm threads. I threaded them until they bottom out and back oit 1 full turn, then used lock nut to tighten them down that way you arent tightening up on the threads in the head.. If you DO have oil on the underside of the head, replace headgasket and repeat sll steps. And dont forget to mind the timing chain.... use a hammer to hold it up after you move the cam becsue if it drops, youre gonna have a bad time... also, buy new header gaskets..... Phew... Last edited by Pmhearns; 06-16-2017 at 11:26 AM.
	0

06-15-2017, 01:54 AM	#2
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	Could be the valve adjust covers. Could be the head gasket. I've fought with this problem too.
	0

07-10-2017, 10:21 PM	#6
leonj2932 Member Join Date: May 2017 Location: San Francisco/Bay Area Posts: 31	no sorry , its definetely something, when i bought the bike there was no oil, 1000 miles later and im just a mess with this bike still.
	0

06-19-2017, 12:10 AM	#10
leonj2932 Member Join Date: May 2017 Location: San Francisco/Bay Area Posts: 31	wow that sounds like a lot of things to do , ugh this bike has been nothin but problems so far .
	0