07-18-2010, 09:11 PM
|
#1 |
|
Junior Member
Join Date: Jul 2010
Location: Kentucky
Posts: 20
|
Link to Valve Adjustments Page
Hello All,
I have seen long threads on adjusting valves, yet no one has provided any nice step by step photos to go along with the procedures. Well, I finally found someone who did. Here is the link: http://i2kdave.wordpress.com/2009/07...ve-adjustment/ Hope it helps Login or Register to Remove Ads |
|
|
|
03-12-2011, 09:07 PM
|
#2 |
|
Junior Member
Join Date: Dec 2010
Location: South Philly
Posts: 8
|
Re: Link to Valve Adjustments Page
This is an excellent write-up, thank you for this link.
|
|
|
|
|
03-13-2011, 12:27 AM
|
#3 |
|
Senior Member
Join Date: May 2010
Location: Abbotsford, BC
Posts: 444
|
Re: Link to Valve Adjustments Page
Yes, this is a great page. I followed these instructions a few weeks ago and it went very smoothly. The only real trouble was getting my 'feeler guage' hand AND the light, AND my eyes in the right position all at the same time. I've never seen a photo of someone actually getting there fingers in there so I'll post mine:
 BTW, I couldn't be bothered to make a trip to the bike shop to get a proper tool to turn the valve screw so I just took a suitable Robertson screw and screwed it into a short chunk of dowel. Worked great! Cheers!
__________________
Lovin' every minute of it. 2005 GZ250 (sold after 26000km) 2013 CB500XA Login or Register to Remove Ads |
|
|
|
|
03-13-2011, 12:37 AM
|
#4 | |
|
Senior Member
Join Date: Feb 2010
Location: P.E.I. Canada
Posts: 3,784
|
Re: Link to Valve Adjustments Page
Quote:
__________________
If at first you do succeed, try not to look surprised. 
|
|
|
|
|
|
03-13-2011, 04:08 AM
|
#6 |
|
Senior Member
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
|
Re: Link to Valve Adjustments Page
After fighting with all sorts of headlights, trouble lights and shadows I finally found something that works. I ran across a ball cap with 2 LED's built into the beak. Puts the light right where I want it. Later I found a small LED clip on that fits a ball cap. They both work very well without the hassle of holding a light, power cords or a lot of heat from a bulb. Batteries are not cheap but working in the Bat Cave underground is kinda dark 100% of the time.
|
|
|
|
|
03-13-2011, 09:29 PM
|
#7 |
|
Senior Member
Join Date: May 2010
Location: Abbotsford, BC
Posts: 444
|
Re: Link to Valve Adjustments Page
Excellent idea! I'll pick up one of those for my kit.
__________________
Lovin' every minute of it. 2005 GZ250 (sold after 26000km) 2013 CB500XA |
|
|
|
|
03-14-2011, 08:49 AM
|
#8 |
|
Super Moderator
Join Date: Jan 2007
Location: Dalton, GA
Posts: 3,996
|
Re: Link to Valve Adjustments Page
The above referenced link has been adapted for the forum and made into a How-to.
Thanks, i2kDave & Brocea! How-To : Valve Adjustment: viewtopic.php?f=8&t=5061 |
|
|
|
|
03-15-2011, 02:52 PM
|
#9 |
|
Junior Member
Join Date: Dec 2010
Location: South Philly
Posts: 8
|
Re: Link to Valve Adjustments Page
I haven't had a chance to get in there yet, so I'm not sure about this.
In the original linked article, there's a comment from a user: "One problem. This bike has forked rocker arms. In order to properly adjust the screw and locknut on a bike that has forked rocker arms, you must have two sets of feeler gauges; one for each arm. If you don’t have that, the fork will tilt to one side, throwing off your adjustment slightly." Do you folks think this is something to be concerned about? |
|
|
|
|
03-15-2011, 02:55 PM
|
#10 |
|
Senior Member
Join Date: May 2009
Location: elgin,tx
Posts: 907
|
Re: Link to Valve Adjustments Page
Adjusted mine one at a time. No problems.
__________________
Standing with the PGR until they stand for me. |
|
|
|
 |
|
|
Linear Mode
