Front fender alternatives.

sedifus · 06-25-2014, 09:37 AM

Hello,

Got this bike second year now, pretty good piece of work. Simple and easy to maintain, perfect fit for a midlife crisis bugger like me.

Now, I managed to screw the front fender up. To rear bolts fell off while riding and front part rubbed against the tire. Tire's OK but the fender needs to be patched.. replaced.. or just ditched.

Two questions:

1. Bolts were pretty tight but they fell off from the vibrations anyway. After almost two years riding?! Should I have used the thread locker?
2. What other fenders might fit this bike?

I am considering purchasing one from the Yamaha Maxim models, they're more narrow but the other measurements seems to add up. And a longer bolts and appropriate spacers might do the job. Never liked that huge original fender anyway, as if you were to put the BMW sign on an Abarth.

Suggestions welcome.

**jonathan180iq** · 06-25-2014, 02:52 PM

What part of the fender was damaged? I would just take a dremel tool and use what's left to create a lower profile fender...

Check out what Ruxpin did to his:

http://www.gz250bike.com/forum/showthread.php?t=3828

Water Warrior 2 · 06-25-2014, 03:45 PM

Blue thread locker is your friend. One drop goes a long way.

sedifus · 06-26-2014, 08:51 AM

The images are no longer there. I was thinking of modifying the fender, too, it is the front part that is damaged and the fender has to be shorten by 3-4 inches. That might work or might just turn ugly.

A couple of nice people at eBay gave me the measurements for Yamaha Maxim '81 front fender, seems like everything adds up more-less except that the fender will be too high since the positioning of the bolt holes on Yamaha sits 2 inches lower. Guess I'll have to search further.

sedifus · 06-26-2014, 08:54 AM

Thanks Warrior, I learned that the hard way. Just lucky didn't end up in a ditch.

**jonathan180iq** · 06-26-2014, 01:06 PM

If there is room on the fork part of the Yamaha fender you can always drill some new holes and just lower the mounting points...

Here are a couple of photos of modified GZ fenders. If you're handy with a dremel and can trace lines, you can do this:

sedifus · 06-26-2014, 03:48 PM

Yeah, this looks pretty good Jonathan. Thanks.

**jonathan180iq** · 06-27-2014, 08:20 AM

Let us know what you finally come up with.

blk90 · 08-04-2014, 04:00 PM

is it necessary to paint up again after cutting? is that too much ugly if you left it without painting ?

Water Warrior 2 · 08-04-2014, 05:36 PM

A little ugly goes a long way. Paint it and make it look like you really care. A job well done is a job to be proud of.

06-25-2014, 09:37 AM	#1
sedifus Junior Member Join Date: Jun 2014 Posts: 7	Front fender alternatives. Hello, Got this bike second year now, pretty good piece of work. Simple and easy to maintain, perfect fit for a midlife crisis bugger like me. Now, I managed to screw the front fender up. To rear bolts fell off while riding and front part rubbed against the tire. Tire's OK but the fender needs to be patched.. replaced.. or just ditched. Two questions: 1. Bolts were pretty tight but they fell off from the vibrations anyway. After almost two years riding?! Should I have used the thread locker? 2. What other fenders might fit this bike? I am considering purchasing one from the Yamaha Maxim models, they're more narrow but the other measurements seems to add up. And a longer bolts and appropriate spacers might do the job. Never liked that huge original fender anyway, as if you were to put the BMW sign on an Abarth. Suggestions welcome. Login or Register to Remove Ads Last edited by sedifus; 06-25-2014 at 09:40 AM.
	0

06-25-2014, 03:45 PM	#3
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Blue thread locker is your friend. One drop goes a long way. Login or Register to Remove Ads
	0

06-26-2014, 08:54 AM	#5
sedifus Junior Member Join Date: Jun 2014 Posts: 7	Thanks Warrior, I learned that the hard way. Just lucky didn't end up in a ditch. Login or Register to Remove Ads
	0

06-25-2014, 02:52 PM	#2
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	What part of the fender was damaged? I would just take a dremel tool and use what's left to create a lower profile fender... Check out what Ruxpin did to his: http://www.gz250bike.com/forum/showthread.php?t=3828
	0

06-26-2014, 08:51 AM	#4
sedifus Junior Member Join Date: Jun 2014 Posts: 7	The images are no longer there. I was thinking of modifying the fender, too, it is the front part that is damaged and the fender has to be shorten by 3-4 inches. That might work or might just turn ugly. A couple of nice people at eBay gave me the measurements for Yamaha Maxim '81 front fender, seems like everything adds up more-less except that the fender will be too high since the positioning of the bolt holes on Yamaha sits 2 inches lower. Guess I'll have to search further.
	0

06-26-2014, 01:06 PM	#6
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	If there is room on the fork part of the Yamaha fender you can always drill some new holes and just lower the mounting points... Here are a couple of photos of modified GZ fenders. If you're handy with a dremel and can trace lines, you can do this:
	1

06-26-2014, 03:48 PM	#7
sedifus Junior Member Join Date: Jun 2014 Posts: 7	Yeah, this looks pretty good Jonathan. Thanks.
	0

06-27-2014, 08:20 AM	#8
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	Let us know what you finally come up with.
	0

08-04-2014, 04:00 PM	#9
blk90 Member Join Date: Jun 2014 Location: Taormina, Italy Posts: 35	is it necessary to paint up again after cutting? is that too much ugly if you left it without painting ?
	0

08-04-2014, 05:36 PM	#10
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	A little ugly goes a long way. Paint it and make it look like you really care. A job well done is a job to be proud of.
	0