Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > General > Free Classifieds > Parts & Accessories

Reply
 
Thread Tools Display Modes
Old 11-16-2011, 07:08 PM   #1
krijay1976
Junior Member
 
Join Date: Nov 2011
Location: Louisiana
Posts: 3
parts

my daughters boyfriend got really unlucky last night. He got in a slight fender bender and while waiting for the cops with a person that was, of course, uninsured. he needs some small parts for me to get him back on the road and of course needs them cheap. he had a pretty bad day because he got fired that same morning.
1. Headlight bucket
2. 7/8th handlebars of any sort.
3. right side cover
4. muffler
5. right footpegbrake lever assembly

In any case i appreciate your time for looking at this.
the best way to reach me is by email since this is the first time i have ever been on this page. I am well known on delphi forums if you want to check on me. I go by biscuit there and i am on the Vstar forum and road glide forums.
My email is: krijay1976@gmail.com. I will also be checking back here if i can.



Login or Register to Remove Ads
krijay1976 is offline  
Reply With Quote
Old 11-16-2011, 09:16 PM   #2
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Re: parts

Hope the young fellow wasn't hurt in the mix up.
Water Warrior 2 is offline  
Reply With Quote
Old 11-17-2011, 04:29 AM   #3
alantf
Senior Member
 
alantf's Avatar
 
Join Date: Nov 2008
Location: Tenerife (Spain)
Posts: 3,718
Re: parts

Regarding the footbrake - If it's not the whole thing that's damaged, just the brake pedal up at a higher angle than normal - you'll probably find that it's just the adjuster plate that holds the adjusting bolt (under the pedal arm) that's bent. It should be horizontal, with the bolt touching the brake lever. If the bike goes down, for some reason the plate seems to get bent. If this is the case, then you just need to remove the adjusting bolt, beat the plate horizontal with a heavy lump hammer, replace & adjust the bolt & locknut, & everything will be o.k. I found this out when I got sideswiped & the bike went down, then again when I applied the front brake with the bars turned at low speed, & the bike went down.
__________________
By birth an Englishman, by the grace of God a Yorkshireman.



Login or Register to Remove Ads
alantf is offline  
Reply With Quote
Old 11-17-2011, 11:39 PM   #4
krijay1976
Junior Member
 
Join Date: Nov 2011
Location: Louisiana
Posts: 3
Re: parts

Thanks, he was not hurt to bad. Little bit of road rash. He did decide that being on a bike was not a good thing for him at this time. I happen to agree with him as he lacks maturity and the attention span it takes to not be killed on the road. I imagine he is going to turn the bike over to me and i will fix it up and either sell it or keep it for the other kids coming up to learn to ride on.
krijay1976 is offline  
Reply With Quote
Old 11-17-2011, 11:39 PM   #5
krijay1976
Junior Member
 
Join Date: Nov 2011
Location: Louisiana
Posts: 3
Re: parts

I'll also be looking at that brake pedal a bit better when i get the bike to my shop. Thanks for the tip.



Login or Register to Remove Ads
krijay1976 is offline  
Reply With Quote
Old 11-18-2011, 01:24 AM   #6
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Re: parts

The young man in question may be somewhat immature but also wise enough not to get in over his head again. Good for him. :rawk:
Water Warrior 2 is offline  
Reply With Quote
Old 11-19-2011, 10:57 PM   #7
5th_bike
Senior Member
 
5th_bike's Avatar
 
Join Date: Oct 2007
Location: HoCo, Maryland
Posts: 1,349
Re: parts

FWIW I have a spare new front brake handle that once I got from someone to replace mine but it doesn't fit my bike, it has a round dial on with with numbers 1 2 3 4, I think to set the point where it starts braking, and mine doesn't have that, thus. If you want it (free) send me a PM.
__________________
2005 "Saturn Black", stock + tach
5th_bike is offline  
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:36 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.